Статті
Permanent URI for this collection
Browse
Browsing Статті by Title
Now showing 1 - 14 of 14
Results Per Page
Sort Options
Item KINETICS OF DESTRUCTION AT THE SURFACE STRENGTHENING OF MACHINE PARTS(Державний університет інтелектуальних технологій і зв'язку, 2023) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Балтянський І. В.; Baltianskyi I.; Левендюк О. В.; Levendiuk O.Studying the influence of various factors on the strengthening effect and the kinetics of destruction of surface-hardened parts under cyclic loading is important for strength and durability calculations. A curve is indicated that characterizes the distribution of residual stresses after surface hardening of a part. The diagrams obtained in the work were constructed as a result of algebraic summation of the original diagrams. The analysis performed makes it possible to explain the nature of the crack occurrence: a crack nucleates under certain conditions under a surface-hardened layer in the core material of the part in a halfcycle of tensile stresses from an external load. The research was carried out on samples made of steel 45 with a boron-chromed diffusion layer obtained by successively saturating the surface with boron and chromium. Широке впровадження в практику прогресивних методів розрахунку несучої здатності та технологічних процесів поверхневого зміцнення деталей дозволяє підвищити їх ресурс при одночасному зниженні матеріалоємності. Вивчення впливу різних факторів на ефект зміцнення та кінетику руйнування поверхнево зміцнених деталей при циклічному навантаженні має важливе значення для розрахункових оцінок міцності та довговічності. Виконані у цьому напрямі роботи показали, що труднощі, які виникають при розрахунку меж витривалості поверхнево зміцнених деталей, пов'язані з роллю залишкових напружень наявністю концентраторів, градієнта напруги в концентраторі і неоднорідністю напружень. Наявність залишкового напруження і напруження, викликаного зовнішнім навантаженням, визначає напружено-деформований стан матеріалу при циклічних навантаженнях деталей. Показано, що науковцями недостатньо уваги приділено питанням дослідження процесу зародження втомних тріщин під поверхнево зміцненим шаром. Розглянуто випадок циклічного навантаження згинанням поверхнево зміцненої круглої деталі з концентратором напружень. Вказано криву, що характеризує розподіл залишкових напружень після поверхневого зміцнення деталі, характер зміни яких наступний: стискають – в поверхневому шарі заданої товщини і розтягують – в серцевині матеріалу деталі (внутрішніх шарах). Отримані в роботі епюри побудовані в результаті алгебраїчного підсумовування вихідних епюр. Операція підсумовування носить формальний характер і виконана тільки для того, щоб уявити загальний характер картини напружено деформованого стану в досліджених областях деталі. Проведений аналіз дозволяє пояснити характер виникнення тріщини: тріщина зароджується за певних умов під поверхнево зміцненим шаром у матеріалі серцевини деталі в напівциклі напружень, що розтягують, від зовнішнього навантаження. Особливий інтерес для практики представляють відомості про розвиток тріщини при циклічному навантаженні поверхнево зміцненої деталі як малоциклової, так і багатоциклової втоми.Item PROBLEM ISSUES OF THE DEVELOPMENT OF NUCLEAR ENERGY(Державний університет інтелектуальних технологій і зв'язку, 2023) Сичов М. І.; Sychov M.; Коломієць Л. В.; Kolomiiets L.The energy system of Ukraine includes power transmission lines of various capacities and generating facilities, the most complex of which are nuclear power plants. The article examines aspects of the development of nuclear energy under the circumstances that have developed in Ukraine today. Ukraine has the largest reserves of uranium ores in Europe and suitable conditions for their use. Currently, the production volumes of fuel for nuclear power plants are insufficient for their development; we do not have our own production of heat-separating elements. In addition, the military industry of Ukraine needs new types of weapons and modern materials based on substances from the enrichment of uranium ore. Україна має потужну та розвинену енергетичну систему. Вона включає в себе лінії електропередачі з розподільними пристроями різної потужності. Другою її складовою є генеруючі потужності (теплоелектростанції, гідро- та акумулюючі станції, вітрові та сонячні станції, атомні електростанції). Атомна енергетика, незважаючи на низку значних аварій у світі, є найбільш надійною, безпечною та економічно вигідною. Найкращі екологічні показники, в тому числі за викидами в атмосферу, мають якраз атомні електростанції. Проблема їх функціонування полягає у розгляді подальших аспектів розвитку атомної енергетики в умовах, що сьогодні склалися в Україні та видобутку сировини. Україна має достатні запаси уранових руд та металів для атомної енергетики, а умови їх залягання придатні та зручні для їх використання. Технологія переробки уранових руд в Україні заснована на вилуговуванні урану з гірської породи, що відбувається під землею, в надійних геологічних умовах. Сьогодні обсяги видобутку та збагачення уранової руди та виробництва палива для атомних електростанцій недостатні для їх розвитку та будівництва нових реакторів. Поки що Україна не має власного виробництва ТВЕЛів, які зараз імпортуються з США. Також залишаються екологічні проблеми при видобутку та переробці уранової руди, проблеми зі зберіганням відходів атомної промисловості. В українському суспільстві і досі існує стереотип заперечення атомної енергетики, який породила низку катастроф (Чорнобиль, Фукусіма та інші). Населення України досі не отримує достатньої інформації про ядерні технології, їх безпеку та переваги. Крім того, військові дії вимагають нових видів зброї, яких раніше в Україні не було, на основі речовин, які отримують під час збагачення уранової руди.Item SOFTWARE QUALITY MANAGEMENT(Державний університет інтелектуальних технологій і зв'язку, 2024) Габер А. А.; Haber A.; Габер В. С.; Haber V.; Мазур Є. О.; Mazur Y.The work examines the state of research and practice in the field of software quality management and gives an assessment of the extent to which existing approaches meet the requirements of new softwareintensive systems. The main categories on which software quality management is based, approaches to software quality management are considered. It is shown that in all the studied models, none included the aspect of communication as one of the quality factors. In the field of software quality, a large number of metrics have been proposed for measurement. But these indicators face problems that also arise from the lack of structure in qualitative models. One problem is that, despite the definition of metrics, quality models do not provide a detailed description of the impact of specific indicators on software quality. Nowadays, there is a need for quality components for communications at all levels and especially in complex systems where this becomes a critical factor over the Internet. Сучасна цифровізація та всебічне застосування інформаційних технологій у всіх галузях промисловості пред'являють підвищені вимоги до управління якістю програмного забезпечення. Дефекти якості в концепціях, які потребують інтенсивного програмного забезпечення створюють високі ризики не тільки для успіху бізнесу, але й для здоров’я та безпеки. В роботі розглядається стан досліджень і практики в області управління якістю програмного забезпечення та дається оцінка того, наскільки існуючі підходи відповідають вимогам нових програмно інтенсивних систем. Розглянуто основні категорії на яких ґрунтується управління якістю програмного забезпечення, підходи до управління якістю програмного забезпечення. Показано, що у всіх досліджуваних моделях жодна не включила аспект комунікації як один із факторів якості. У сфері якості програмного забезпечення запропонована велика кількість метрик для вимірювання. Але ці показники стикаються з проблемами, які також виникають через відсутність структури в якісних моделях. Одна з проблем полягає в тому, що, незважаючи на визначення метрик, моделі якості не дають детального опису впливу конкретних показників на якість програмного забезпечення. Через відсутність чіткої семантики агрегація значень метрики за ієрархічними рівнями є проблематичною. У всіх досліджуваних моделях жодна не включила аспект комунікації як один із факторів якості. В даний час існує потреба в якісних компонентах для комунікацій на всіх рівнях і особливо в складних системах, де це стає критичним фактором через Інтернет. В більшості досліджуваних моделей фактори та критерії мають однакове значення, яке є відносним, оскільки залежить від області застосування. Наприклад, аспекти передачі можуть мати вирішальне значення в програмному забезпеченні, яке встановлено на різних машинах.Item TWO-GYROSCOPIC SENSITIVE ELEMENT OF THE STABILIZATION COMPLEX(Державний університет інтелектуальних технологій і зв'язку, 2023) Безвесільна О. М.; Bezvesilna О.; Коломієць Л. В.; Kolomiiets L.; Киричук Ю. В.; Kyrychuk Y.; Толочко Т. О.; Tolochko T.The proposed two-gyroscopic SE is designed to measure acceleration and belongs to the area of acceleration measurements on a moving base and can be used in stabilization systems. The purpose of the article is to increase the accuracy of acceleration determination. To do this, it is necessary to eliminate methodical errors of gyroscopic moments-obstacle from the cross angular velocities of the base and from the angular velocity of the Earth's rotation. The proposed two-gyro SE consists of a three-stage gyroscope located in the inner and outer frames, equipped with an inter-frame correction system, which includes an angle sensor located on the axis of the inner frame of the gyroscope, the output of which is connected to a moment sensor located on the axis of the outer frame. What is new in the two-gyro SE stabilizer is the application on the axis of the inner frame of the gyroscope with the possibility of rotating the rotor in the opposite direction of the main gyroscope, equipped with an inter frame correction system, which includes an electric angle sensor located on the axis of the inner frame of the gyroscope, to the output of which the control winding of the electric moment sensor is connected. Located on the axis of the outer frame, and both gyroscopes are equipped with two additional angle sensors located on the axes of the outer frames, the outputs of which are connected to two additional moment sensors located on one axis of the inner frame, the centers of gravity of the two three-stage gyroscopes are equally shifted to one side along the axes of rotation gyroscope rotors relative to the axes of the outer frames. Пропонований двогіроскопічний чутливий елемент призначений для вимірювання прискорення та відноситься до області вимірювань прискорення на рухомій основі і може використовуватися в системах стабілізації. Метою статті є підвищення точності визначення прискорення. Для цього необхідно усунути методичні похибки гіроскопічних моментів – перешкод від поперечних кутових швидкостей основи і від кутової швидкості обертання Землі. Чутливий елемент складається з триступінчастого гіроскопа, розташованого у внутрішній і зовнішній рамах, оснащеного системою міжрамкової корекції, яка включає датчик кута розташований на осі внутрішньої рами гіроскопа, вихід якого підключений до розташованого на осі зовнішньої рами датчика моменту. Новим у конструкції чутливого елементу комплексу стабілізації є застосування на осі внутрішньої рами гіроскопа з можливістю обертання ротора в протилежну сторону основного гіроскопа, оснащеного системою міжрамкової корекції, яка включає в себе електричний датчик кута розташований на осі внутрішньої рами гіроскопа, до виходу якого підключена керуюча обмотка датчика електричного моменту, розташованого на осі зовнішньої рами, а обидва гіроскопи оснащені двома додатковими датчиками кута розташовані на осях зовнішніх рамок, виходи яких з’єднані з двома додатковими датчиками моменту, розташованими на одній осі внутрішньої рамки, центри ваги двох триступеневих гіроскопів однаково зміщені в одну сторону по осях обертання роторів гіроскопа відносно осей зовнішніх рам. Застосування двогіроскопічного чутливого елементу забезпечує більш високу точність вимірювань, на відміну від одногіроскопічного, за рахунок компенсації похибок поперечних кутових швидкостей і кутової швидкості обертання Землі.Item АНАЛІЗ МЕТОДІВ ВЕЙВЛЕТ-ПЕРЕТВОРЕНЬ В ЗАДАЧАХ СТИСНЕННЯ ЗОБРАЖЕНЬ(Державний університет інтелектуальних технологій і зв'язку, 2022) Солодка В. І.; Solodka V.; Тимошевський О. В.; Tymoshevskyi O.В роботі проводиться аналіз за допомогою спектральних перетворень для отримання показників стиснення та відношення сигнал/шум, найкращим вейвлет базисом, а саме окремий випадок перетворення Фур’є для стиснення зображень за значенням відношення сигнал/шум. Також проводиться проектування сіткового об’ємного об’єкта в двовимірні координати, для видалення невидимих вершини і відрізків. Показано, що з метою зменшення потоку даних доцільно перед перетворенням тривимірного сіткового зображення в двовимірне проводити спектральне вейвлет-перетворення. При видаленні незначних вейвлет-коефіцієнтів можливо досягти стиснення в 5 разів, при цьому якість зображення, представлене ставленням сигнал/шум, досягає значення 35 дБ – оцінка показника прийнятного візуальної якості для комфортного перегляду. In this work, an analysis is carried out using spectral transformations to obtain compression indicators and signal-to-noise ratio, the best wavelet basis, namely, a special case of the Fourier transform for image compression according to the signal-to-noise ratio criteria. The increase in the compression ratio with increasing Dobeshi order is shown due to the fact that increasing the order increases the scaling function, which allows to increase the degree of compression of the image, obtaining a satisfactory quality of this image. But with increasing scaling function, the length of the filter increases, which complicates the implementation of this method. Spectral transformations in the problems of image compression in modern algorithms are shown that they can increase the compression ratio of black and white and color images with a comparative visual quality in relation to the algorithms of the previous generation, based on discrete cosine transform. Also, the design of a mesh volumetric object in two-dimensional coordinates is carried out to remove invisible vertices and segments. A study of the transfer of the remainder in the two-dimensional field of vertices during alternation and sequential television scans. It is shown that in order to reduce the data flow, it is advisable to perform a spectral wavelet transform before transforming a three-dimensional grid image into a twodimensional one. By removing insignificant values of the wavelet coefficients, it is possible to achieve compression by a factor of 5, while the image quality represented by the signal-to-noise ratio reaches 35 dB – an estimate of the indicator of acceptable visual quality for comfortable viewing.Item ВИЗНАЧЕННЯ НАПРУЖЕНО-ДЕФОРМІВНОГО СТАНУ ПРУЖНИХ ЕЛЕМЕНТІВ ТЕНЗОМЕТРИЧНИХ ДАТЧИКІВ СИЛИ(Державний університет інтелектуальних технологій і зв'язку, 2023) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Передерко А. Л.; Perederko A.; Цимбалюк А. Г.; Tsymbaliuk A.; Цимбалюк Д. А.; Tsymbaliuk D.У статті показано, що при вимірюванні зусиль ваговими пристроями у тривалих динамічних процесах особливе значення набуває збереження метрологічних параметрів тензорезисторних датчиків сили в певному часовому інтервалі. Силовимірювальні ланцюги вагових пристроїв виконують таким чином, щоб пружний елемент працював у зоні пружних деформацій. Існування різноманітних форм пружних елементів викликає математичні труднощі під час вирішення відповідних задач теорії пружності. При цьому урахування динамічних доданків зовнішніх впливів на пружний елемент значно ускладнює процес побудови розв’язку. Як показав аналіз досліджень і відомих публікацій, вкрай необхідним для визначення напружено-деформівного стану пружних елементів є застосування одного із ефективних видів чисельних методів розрахунку – методу скінченних елементів, який є основою скінченно-елементного пакета ANSYS та дозволяє проєктувати конструкції силомірних пристроїв при зміні навантажень в широкому діапазоні. The article shows that when measuring forces with weighing devices in long-term dynamic processes, the preservation of metrological parameters of tensor-resistor force sensors in a certain time interval acquires special importance. The causes of similar failures of force sensors can be fatigue phenomena occurring in the material of the elastic element. Functional failure associated with fatigue phenomena of the material of the elastic element is usually observed long before its complete destruction. Therefore, force-measuring chains of weighing devices are made in such a way that the elastic element works in the zone of elastic deformations. This is also explained by the fact that in the presence of plastic deformations, hysteresis phenomena appear which reduces the accuracy of measurements. The existence of various forms of elastic elements causes mathematical difficulties when solving the corresponding problems of the theory of elasticity. At the same time, accounting for the dynamic terms of external influences on the elastic element significantly complicates the process of constructing a solution. Without taking into account dynamic components, it is difficult to perform optimal design of elastic elements of force sensors of weighing systems. As the analysis of research and well-known publications showed, it is absolutely necessary to determine the stress-strain state of elastic elements using one of the effective types of numerical calculation methods – the finite element method, which is the basis of the ANSYS finite element package and allows designing the structures of force measuring devices when loads change in a wide range. The analysis of the results of the research of the VAT of the elastic element of the cylindrical force sensor with cutouts shows that the location of the tensor resistors at the minimum distance to the axis of symmetry of the elastic element, in the zone of maximum deformations, is optimally chosen, which allows to reduce the influence of negative factors on the accuracy and stability of the measurement results.Item ДОСЛІДЖЕННЯ КОНСТРУКЦІЙ ЗАПОБІЖНИХ ПРИСТРОЇВ ПІДЙОМНИХ МАШИН(Державний університет інтелектуальних технологій і зв'язку, 2024) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Передерко А. Л.; Perederko A.; Цимбалюк Д. А.; Tsymbaliuk D.У статті розглядаються конструкції запобіжників від перевантаження підйомних машин, які монтуються на вантажних канатах. Встановлено, що до недоліків даного типу конструкцій відноситься похибка вимірювань в межах 5-6 %, яка виникає внаслідок впливу дотичних сил на передавальні елементи запобіжного пристрою. Однак за рахунок своєї надійності, простоти та низької вартості ці пристрої якраз і набули широкого поширення в кранобудуванні. Отримані аналітичні залежності визначення загальної похибки, які виникають внаслідок втрат на канатному відхиляючому блоці підйомної машини. Проведені натурні випробування запобіжного пристрою для кранів мостового типу вантажопідйомністю до трьох тон. Результати випробувань підтвердили достатню для даного типу запобіжників точність та надійність спрацьовування. The article examines the designs of support structures for the re-installation of lifting machines, which are mounted on suspended ropes. The object of investigation is theft, which stems from the costs of the rope suction block of an overhead crane. The method of work is to track warehouse costs on the rope suction block of an overhead crane, which affects the accuracy and reliability of the work of the associated device. It has been established that up to a short period of time this type of structure exhibits a loss of vibration in the range of 5 - 6 %, which is due to the influx of additional forces on the transmission elements of the secondary device. However, due to its reliability, simplicity and low cost of construction, there has been a wide expansion in the crane industry. Investigations of the losses that occur when the tension of the rope is tightened, which is due to the instrumental deformation of the device, and methodically, which arises from the chopping of the diameter of the rope in order to reach the end of its life, hitting the block and spending on blocks. Removing the analytical significance of the significant losses that result from the expenses on the rope ventilating block of the lifting machine. A full-scale testing of an external device for overhead cranes of the vantage type with a capacity of up to three tones was carried out. The test results confirmed the accuracy and reliability of application for this type of assistant. To reduce the damage caused by friction in the bearings of the block and on the heeled rigidity of the rope, it was necessary to install an additional device in the place where the rope is secured.Item ЕКСПЕРТИЗА ОСВІТНІХ ТЕХНОЛОГІЙ У ТЕХНІЧНОМУ ЗАКЛАДІ ВИЩОЇ ОСВІТИ(Державний університет інтелектуальних технологій і зв'язку, 2023) Кисельова О. І.; Kyselova O.; Коломієць Л. В.; Kolomiiets L.; Грабовський О. В.; Hrabovskyi O.У статті визначено зміст освітньої технології та її ознаки; сутність експертизи освітньої технології впроваджуваної в сучасному технічному ЗВО, етапи та критерії її проведення. Представлено процедуру експертизи освітніх технологій у технічному закладі вищої освіти, перший етап якої передбачав опитування учасників освітнього процесу, за розробленим опитувальником для оцінки придатності та ефективності застосовуваних технологій (дослідження проводилось в Державному університеті інтелектуальних технологій і зв’язку); за результатами опитування студентів і викладачів визначено, що респонденти розглядають освітню технологію, яка передбачає змішану форму навчання, як вимогу часу, спричинену зовнішніми впливами, переважна більшість опитаних вважають її досить ефективною і сучасною, але такою, яка не спроможна повністю забезпечити всі запити учасників освітнього процесу та потребує певних удосконалень. The article defines the content of educational technology and its features; the essence of the examination of educational technology implemented in modern technical higher education institutions, the stages and criteria of its implementation. The analyzed educational technology involves the use of technical means and programmed learning, is a tool for improving the organization of the educational process, is focused on the modernization of educational activities, in accordance with the demands of society. The procedure for determining the effectiveness of educational technology is presented, which is based on the measurement of the time spent and the calculation of the productivity coefficient, which relates the acquired professional competences to the speed of work performance. The procedure of examination of educational technologies in a technical institution of higher education is presented, the first stage of which involved surveying the participants of the educational process according to a developed questionnaire to assess the suitability and effectiveness of the technology used (the study was conducted at the State University of Intellectual Technologies and Communication). Respondents were asked questions about the relevance, efficiency, quality assurance of the educational process, its effectiveness, the formation of a "resource of success" and the competitiveness of graduates. According to the results of the survey of students and teachers, it was determined that they consider educational technology, which involves a mixed form of learning, as a time requirement caused by external influences, the vast majority of respondents consider it quite effective and modern, but not able to fully satisfy all the requests of participants in the educational process, in in the future, it needs certain improvements.Item ОРГАНІЗАЦІЙНО-ІНФОРМАЦІЙНИЙ ПІДХІД ДО ДИЗАЙНУ ЗАКЛАДУ ВИЩОЇ ОСВІТИ В КОНТЕКСТІ ЖИТТЄВОГО ЦИКЛУ СИСТЕМИ(Державний університет інтелектуальних технологій і зв’язку, 2024) Коломієць Л. В.; Kolomiiets L.; Кисельова О. І.; Kyselova O.; Грабовський О. В.; Hrabovskyi O.У статті обґрунтована необхідність застосування організаційно-інформаційного підходу до дизайну закладу вищої освіти в контексті життєвого циклу системи. Представлена модель типового життєвого циклу системи; згідно визначення організаційно-інформаційного дизайну ЗВО, як складної системи, визначено її рівні і складові. З метою усунення недоліків оцінювання якості функціонування системи вищої освіти, на прикладі закладу вищої освіти, запропоновано процесний підхід до визначення якості надання освітніх послуг. В ході дослідження розроблено процесну модель якості організаційно- інформаційного дизайну ЗВО, представлено схему життєвого циклу цільової системи відповідно до ISO 24748-1 та візуалізації процесної моделі штучної системи у вигляді загальної V-моделі, подано ієрархічну систему якісних показників, що формують структуру моделі якості. The article substantiates the need to apply an organizational and information approach to the design of a higher educational institution in the context of the system's life cycle. This was determined by an analysis of existing approaches and methods to determining the effectiveness of the provision of educational services by higher education institutions. It has been proven that, despite all their classical completeness, there are significant drawbacks. These include: the educational services market introduced in Ukraine is not taken into account; application of methods for monitoring and assessing knowledge based on the final result. All this does not allow us to analyze many factors at intermediate stages that influence the quality of educational services. A model of a typical system life cycle with stages is presented: system design; system development; production system; system operation/support; decommissioning (disposal) of the system. According to the definition of the organizational and information design of a university as a complex system, its levels and components are defined: level zero – the target system, that is, the university under study; the first level is the strategic peak; second level – midline; the third level is the operating core; auxiliary structure. It has been established that universities have their own specifics, based on the analysis of which, a new type of design has been developed, namely organizational and information design and its model, which provides a systematic organization in accordance with the specifics of an individual university. In order to eliminate shortcomings in assessing the quality of functioning of a higher educational institution, a process approach to determining the quality of educational services is proposed. During the study, a process model of the quality of organizational and information design of a higher educational institution was developed, a life cycle diagram of the target system was presented in accordance with ISO 24748-1 and a visualization of the process model of the artificial system in the form of a general V-model was presented, a hierarchical system of quality indicators that form the structure of the model was presented.Item ПЕРЕВАГИ ТА НЕДОЛІКИ АВТОНОМНИХ СОНЯЧНИХ ЕЛЕКТРОСТАНЦІЙ(Державний університет інтелектуальних технологій і зв'язку, 2024) Габер А. А.; Haber A.; Зіангірова Л. Т.; Zianhirova L.; Берменко Ю. В.; Bermenko Y.; Габер В. С.; Haber V.В статті розглядається стан досліджень і практики використання автономних сонячних електростанцій, переваг та недоліків їх використання у побуті. Розглянуто основні поняття сонячної енергії, автономності та складових сонячних електростанцій. Розглянуто діючі нормативні документи щодо досліджуваного питання. The article examines the state of research and practice of using autonomous solar power plants, the advantages and disadvantages of their use in everyday life. The main concepts of solar energy, autonomy and components of solar power plants are considered. Current normative documents regarding the researched issue are considered. Solar energy is obtained from solar radiation and can be transformed into electricity or heat. It is freely available, and thanks to advances in technology, we can now use even more of the solar energy that is constantly available to us. Solar energy has the least negative impact on the environment compared to any other energy source. It does not emit greenhouse gases and does not pollute water. Its maintenance also requires very little water, unlike, for example, nuclear power plants, which require 20 times more water. The production of solar energy does not create any noise, which is a big advantage, since many solar installations, such as residential solar panels, are located in urban areas. Solar power plants are quite innovative equipment. Solar energy is one of the most dynamically developing branches of alternative (renewable) energy. Solar energy is developing at an increasing pace and has already turned into a powerful industry in the world's largest economies. In Ukraine, the growth rate of solar energy accelerated this year. Solar energy for residential buildings is a hot topic today.Item ПЛІВКОВА КОНДЕНСАЦІЯ У СЕРЕДИНІ ГОРИЗОНТАЛЬНИХ ТРУБ ТА МІНІКАНАЛІВ(Державний університет інтелектуальних технологій і зв'язку, 2022) Горін В. В.; Horin V.; Коломієць Л. В.; Kolomiiets L.; Середа В. В.; Sereda V.У праці наведено короткий опис напівемпіричної моделі Ананьєва, Бойко і Кружиліна щодо розрахунку тепловіддачі під час конденсації робочих речовин у середині гладких горизонтальних труб у разі турбулентного режиму течії потоку. Представлено порівняння розрахунків тепловіддачі за напівемпіричною моделлю з результатами експериментальних досліджень щодо конденсації холодоагентів, гідрокарбонів та спеціалізованих речовин у середині труб із відомих праць різних авторів, які свідчать про добре узгодження результатів досліджень із розрахунками за зазначеною моделлю із урахуванням їх граничних величин. The article provides a brief description of the semi-empirical model of Ananiev, Boyko and Kruzhilin for calculating heat transfer during the condensation of working substances inside smooth horizontal pipes in a turbulent flow regime. Comparisons of heat transfer calculations based on a semi-empirical model with the results of experimental studies during the condensation of refrigerants, hydrocarbons and specialized substances inside pipes from well-known works by different authors are presented, which indicate good agreement between the results of studies and calculations based on the model, taking into account their boundary values. The presented calculations of heat transfer during condensation inside smooth horizontal pipes and minichannels are performed according to the semiempirical formula of Ananiev, Boyko and Kruzhilin, taking into account the influence of steam velocity on heat transfer processes. The calculation results demonstrate good agreement with the experimental data of various authors on the condensation of refrigerants R22, R134a, R125, R32 , R410A, specialized substances R245fa, Novec649, HFE-7000 and natural hydrocarbons R290, R600a, R1270, and DME for turbulent flow areas. For engineering practice, the presented semi-empirical model for calculating heat transfer during condensation of water vapor, refrigerants R22, R134a, R32, R410A, specialized substance HFE-7000, natural hydrocarbons R290, R600a, R1270 for smooth horizontal pipes (din > 3 mm) can be recommended. In this case, it is necessary to take into account the limits of application of the boundary values of the model. Calculation of heat transfer coefficients by semi-empirical correlation shows that it improves the description of the experimental data of many authors of works on the condensation of refrigerants R152a, R290, R134a, and R32 inside round minichannels (3 mm ≥ din > 200 μm) under turbulent and transient flow regimes. Further studies should include the performance of calculations on theoretical and empirical models for calculating heat transfer during condensation inside minichannels in order to create a general method for calculating heat transfer, taking into account the influence of regime flow parameters.Item ПІДВИЩЕННЯ ПРОПУСКНОЇ ЗДАТНОСТІ ТРАНСПОРТНОЇ МЕРЕЖІ ЗВ’ЯЗКУ ІВАНО-ФРАНКІВСЬКОЇ ОБЛАСТІ(Державний університет інтелектуальних технологій і зв'язку, 2024) Думич О. О.; Dumych O.; Бугеда Л. К.; Buheda L.Ще донедавна здавалося, що впровадження систем SDH, які працюють на волоконно-оптичному кабелі, вирішує всі проблеми на далеку перспективу розвитку первинної мережі зв’язку. Але не минуло й десяти років з моменту появи перших магістральних ВОСП, як виявилося, що їхня пропускна здатність виявилася недостатньою. Потрібно було або збільшувати швидкість передачі даних на найбільш завантажених ділянках, або шукати нові підходи до розбудови первинної мережі зв’язку. Поява технології WDM значно полегшила вирішення цієї проблеми. Для магістральної мережі оптимальним рішенням стали системи DWDM (Dense Wavelength Division Multiplexing) – системи з щільним спектральним розділенням каналів, а також системи CWDM (Coarse Wavelength Division Multiplexing) – системи з грубим спектральним розділенням каналів. CWDM переважно впроваджуються на міських мережах зв’язку.Item РОЗРОБКА ТА ВПРОВАДЖЕННЯ ТРАНСПОРТНИХ МЕРЕЖ, ВИКОРИСТОВУЮЧИ ОБЛАДНАННЯ ВІД HUAWEI(Державний університет інтелектуальних технологій і зв'язку, 2024) Петрушевський О. С.; Petrushevskyi O.; Бугеда Л. К.; Buheda L.Сучасний світ, насичений високими технологіями та постійною еволюцією, покладає на країни величезні завдання щодо забезпечення сталого розвитку. Одним з ключових факторів досягнення цієї мети є активне впровадження новітніх технологій у сфері телекомунікацій. Технологічний прогрес у цій галузі не лише стимулює економічний розвиток, але й формує основу для соціально прогресивного суспільства. Ефективні та передові технології у телекомунікаціях надають можливості для створення динамічної та прозорої системи управління нацією. Сприяючи розвитку держави, бізнесу та кожного окремого громадянина, вони визначають нові стандарти економічного та соціального функціонування [1].Item ТЕОРЕТИКО-МЕТОДОЛОГІЧНІ ЗАСАДИ ЕКСПЕРТИЗИ ОСВІТНЬОГО ПРОЦЕСУ ЗАКЛАДУ ВИЩОЇ ОСВІТИ(Державний університет інтелектуальних технологій і зв'язку, 2022) Кисельова О. І.; Kyselova O.; Коломієць Л. В.; Kolomiiets L.; Передерко А. Л.; Perederko A.; Грабовський О. В.; Hrabovskyi О.У статті визначено основні теоретико-методологічні засади експертизи освітнього процесу закладу вищої освіти, узагальнено характеристики експертизи, класифіковано об’єкти і процеси приналежні освітньому процесу ЗВО, що підлягають експертному вивченню. Досліджено ряд загальнонаукових методологічних підходів, функцій та методів експертизи освітнього процесу, проаналізовано їхню ефективність та доцільність застосування в умовах освітнього процесу ЗВО. Доведено що, науково-методологічне обґрунтування впровадження технологій педагогічної експертизи засновано на зведені в єдину матрицю різних показників змісту освітньої діяльності ЗВО: змісту освіти, освітніх, розвиваючих і виховних цілей; аналізу освітніх ситуацій, методів, засобів, форм навчання і контролю; врахування зворотного і міждисциплінарних зв’язків; інтелектуального розвитку студентів; компетентності викладачів; інноваційності, полікомпонентності та професійної спрямованості навчання в ЗВО. The article defines the main theoretical and methodological foundations of the examination of the educational process of the university, it belongs to the cluster of humanitarian examinations - this is a kind of pedagogical examination, which consists of a number of procedures necessary for the creation and subsequent implementation of the results covered in the collective conclusion, expert assessment (or judgment) about the object under study (pedagogical object, phenomenon or process). The characteristics of pedagogical expertise, which are inherent not only to it, but also to other scientific methods of research, for example, objectivity, criticality, compliance of the assessed object with legislative norms, that is, they do not determine the essence of the method of pedagogical expertise, in contrast to such as: requirements, collectivity, predictability to experts. These are properties, the totality of which describes the essence of expertise as a scientific method. The objects of pedagogical expertise are conditionally divided into two categories: objects of the first order: the activities of the university, didactic research, the quality of education - these are generalized categories that combine objects of the second order (for example, the quality of education is determined by assessing students’ knowledge, building their professiograms, using pedagogical technologies and methods etc., examinations of objects of the second order can be carried out at the same time. The functions of the examination of the educational process characterize it as an examination of the humanitarian direction and at the same time combine it with other methods of socially oriented and person-centered research. is based on various indicators of the content of the educational activities of the university, summarized in a single matrix: the content of education, educational, developmental and educational goals; analysis of educational situations, methods, means, forms of education and control; accounting for feedback and interdisciplinary links; intellectual development of students; competence of teachers; innovativeness, multicomponent and professional orientation of education at the university.