Browsing by Author "Lymarenko O."
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item KINETICS OF DESTRUCTION AT THE SURFACE STRENGTHENING OF MACHINE PARTS(Державний університет інтелектуальних технологій і зв'язку, 2023) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Балтянський І. В.; Baltianskyi I.; Левендюк О. В.; Levendiuk O.Studying the influence of various factors on the strengthening effect and the kinetics of destruction of surface-hardened parts under cyclic loading is important for strength and durability calculations. A curve is indicated that characterizes the distribution of residual stresses after surface hardening of a part. The diagrams obtained in the work were constructed as a result of algebraic summation of the original diagrams. The analysis performed makes it possible to explain the nature of the crack occurrence: a crack nucleates under certain conditions under a surface-hardened layer in the core material of the part in a halfcycle of tensile stresses from an external load. The research was carried out on samples made of steel 45 with a boron-chromed diffusion layer obtained by successively saturating the surface with boron and chromium. Широке впровадження в практику прогресивних методів розрахунку несучої здатності та технологічних процесів поверхневого зміцнення деталей дозволяє підвищити їх ресурс при одночасному зниженні матеріалоємності. Вивчення впливу різних факторів на ефект зміцнення та кінетику руйнування поверхнево зміцнених деталей при циклічному навантаженні має важливе значення для розрахункових оцінок міцності та довговічності. Виконані у цьому напрямі роботи показали, що труднощі, які виникають при розрахунку меж витривалості поверхнево зміцнених деталей, пов'язані з роллю залишкових напружень наявністю концентраторів, градієнта напруги в концентраторі і неоднорідністю напружень. Наявність залишкового напруження і напруження, викликаного зовнішнім навантаженням, визначає напружено-деформований стан матеріалу при циклічних навантаженнях деталей. Показано, що науковцями недостатньо уваги приділено питанням дослідження процесу зародження втомних тріщин під поверхнево зміцненим шаром. Розглянуто випадок циклічного навантаження згинанням поверхнево зміцненої круглої деталі з концентратором напружень. Вказано криву, що характеризує розподіл залишкових напружень після поверхневого зміцнення деталі, характер зміни яких наступний: стискають – в поверхневому шарі заданої товщини і розтягують – в серцевині матеріалу деталі (внутрішніх шарах). Отримані в роботі епюри побудовані в результаті алгебраїчного підсумовування вихідних епюр. Операція підсумовування носить формальний характер і виконана тільки для того, щоб уявити загальний характер картини напружено деформованого стану в досліджених областях деталі. Проведений аналіз дозволяє пояснити характер виникнення тріщини: тріщина зароджується за певних умов під поверхнево зміцненим шаром у матеріалі серцевини деталі в напівциклі напружень, що розтягують, від зовнішнього навантаження. Особливий інтерес для практики представляють відомості про розвиток тріщини при циклічному навантаженні поверхнево зміцненої деталі як малоциклової, так і багатоциклової втоми.Item ВИЗНАЧЕННЯ НАПРУЖЕНО-ДЕФОРМІВНОГО СТАНУ ПРУЖНИХ ЕЛЕМЕНТІВ ТЕНЗОМЕТРИЧНИХ ДАТЧИКІВ СИЛИ(Державний університет інтелектуальних технологій і зв'язку, 2023) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Передерко А. Л.; Perederko A.; Цимбалюк А. Г.; Tsymbaliuk A.; Цимбалюк Д. А.; Tsymbaliuk D.У статті показано, що при вимірюванні зусиль ваговими пристроями у тривалих динамічних процесах особливе значення набуває збереження метрологічних параметрів тензорезисторних датчиків сили в певному часовому інтервалі. Силовимірювальні ланцюги вагових пристроїв виконують таким чином, щоб пружний елемент працював у зоні пружних деформацій. Існування різноманітних форм пружних елементів викликає математичні труднощі під час вирішення відповідних задач теорії пружності. При цьому урахування динамічних доданків зовнішніх впливів на пружний елемент значно ускладнює процес побудови розв’язку. Як показав аналіз досліджень і відомих публікацій, вкрай необхідним для визначення напружено-деформівного стану пружних елементів є застосування одного із ефективних видів чисельних методів розрахунку – методу скінченних елементів, який є основою скінченно-елементного пакета ANSYS та дозволяє проєктувати конструкції силомірних пристроїв при зміні навантажень в широкому діапазоні. The article shows that when measuring forces with weighing devices in long-term dynamic processes, the preservation of metrological parameters of tensor-resistor force sensors in a certain time interval acquires special importance. The causes of similar failures of force sensors can be fatigue phenomena occurring in the material of the elastic element. Functional failure associated with fatigue phenomena of the material of the elastic element is usually observed long before its complete destruction. Therefore, force-measuring chains of weighing devices are made in such a way that the elastic element works in the zone of elastic deformations. This is also explained by the fact that in the presence of plastic deformations, hysteresis phenomena appear which reduces the accuracy of measurements. The existence of various forms of elastic elements causes mathematical difficulties when solving the corresponding problems of the theory of elasticity. At the same time, accounting for the dynamic terms of external influences on the elastic element significantly complicates the process of constructing a solution. Without taking into account dynamic components, it is difficult to perform optimal design of elastic elements of force sensors of weighing systems. As the analysis of research and well-known publications showed, it is absolutely necessary to determine the stress-strain state of elastic elements using one of the effective types of numerical calculation methods – the finite element method, which is the basis of the ANSYS finite element package and allows designing the structures of force measuring devices when loads change in a wide range. The analysis of the results of the research of the VAT of the elastic element of the cylindrical force sensor with cutouts shows that the location of the tensor resistors at the minimum distance to the axis of symmetry of the elastic element, in the zone of maximum deformations, is optimally chosen, which allows to reduce the influence of negative factors on the accuracy and stability of the measurement results.Item ДОСЛІДЖЕННЯ КОНСТРУКЦІЙ ЗАПОБІЖНИХ ПРИСТРОЇВ ПІДЙОМНИХ МАШИН(Державний університет інтелектуальних технологій і зв'язку, 2024) Коломієць Л. В.; Kolomiiets L.; Лимаренко О. М.; Lymarenko O.; Передерко А. Л.; Perederko A.; Цимбалюк Д. А.; Tsymbaliuk D.У статті розглядаються конструкції запобіжників від перевантаження підйомних машин, які монтуються на вантажних канатах. Встановлено, що до недоліків даного типу конструкцій відноситься похибка вимірювань в межах 5-6 %, яка виникає внаслідок впливу дотичних сил на передавальні елементи запобіжного пристрою. Однак за рахунок своєї надійності, простоти та низької вартості ці пристрої якраз і набули широкого поширення в кранобудуванні. Отримані аналітичні залежності визначення загальної похибки, які виникають внаслідок втрат на канатному відхиляючому блоці підйомної машини. Проведені натурні випробування запобіжного пристрою для кранів мостового типу вантажопідйомністю до трьох тон. Результати випробувань підтвердили достатню для даного типу запобіжників точність та надійність спрацьовування. The article examines the designs of support structures for the re-installation of lifting machines, which are mounted on suspended ropes. The object of investigation is theft, which stems from the costs of the rope suction block of an overhead crane. The method of work is to track warehouse costs on the rope suction block of an overhead crane, which affects the accuracy and reliability of the work of the associated device. It has been established that up to a short period of time this type of structure exhibits a loss of vibration in the range of 5 - 6 %, which is due to the influx of additional forces on the transmission elements of the secondary device. However, due to its reliability, simplicity and low cost of construction, there has been a wide expansion in the crane industry. Investigations of the losses that occur when the tension of the rope is tightened, which is due to the instrumental deformation of the device, and methodically, which arises from the chopping of the diameter of the rope in order to reach the end of its life, hitting the block and spending on blocks. Removing the analytical significance of the significant losses that result from the expenses on the rope ventilating block of the lifting machine. A full-scale testing of an external device for overhead cranes of the vantage type with a capacity of up to three tones was carried out. The test results confirmed the accuracy and reliability of application for this type of assistant. To reduce the damage caused by friction in the bearings of the block and on the heeled rigidity of the rope, it was necessary to install an additional device in the place where the rope is secured.